# Test Plugin Scale Units

**URL:** <https://forum.quantasylum.com/t/test-plugin-scale-units/117>\
**Category:** QA401\
**Created:** [June 13, 2020, 8:05am UTC](https://forum.quantasylum.com/t/test-plugin-scale-units/117 "2020-06-13T08:05:43Z")\
**Posts on this page:** 3\
**Page:** 1

<div class="post-metadata">

**Author:** ![M2Circuits](https://avatars.discourse-cdn.com/v4/letter/m/ecb155/32.png) [@M2Circuits](https://forum.quantasylum.com/u/M2Circuits)\
**Post date:** [June 13, 2020, 8:05am UTC](https://forum.quantasylum.com/t/test-plugin-scale-units/117/1 "2020-06-13T08:05:43Z")

</div>

I just received my QA401 this week, and so far I am very pleased with the unit and software.

My questions is, is there any way to change the scale from dBV to dBm for the test plugins?

I know you can change it in the side control panel, but that doesn’t seem to change the it for the test plugins - just the active display and general user interface. I work more in dBm than dBV, and would like the test plugin graph scales to be in dBm. I plan on mostly using the AMP Frequency Response test plugin.

Thanks!

---

<div class="post-metadata">

**Author:** ![matt](https://avatars.discourse-cdn.com/v4/letter/m/a6a055/32.png) [@matt](https://forum.quantasylum.com/u/matt)\
**Post date:** [June 18, 2020, 3:35pm UTC](https://forum.quantasylum.com/t/test-plugin-scale-units/117/2 "2020-06-18T15:35:15Z")

</div>

Hi @M2Circuits, there’s no way currently to change the units to dBm. But you could fiddle with offsets and do it. Assume we’re talking about a 600 ohm system (recompute for whatever characteristic impedance you wish):

```auto
0 dBV = 1Vrms = 1.66 mW = 2.21 dBm
6 dBV = 2Vrms = 6.66 mW = 8.21 dBm
12 dBV = 4Vrms = 26.6 mW = 14.21 dBm

```

Note to go from 0 dBV into 600 ohms to dBm requires you to add 2.21 dB. And then, 6 dB more voltage yields 6 dB more power. And 12 dB more voltage yields 12 dB more power. So, if I add an external input gain of -2.21 dB in the plugin setup:

 ![image](https://canada1.discourse-cdn.com/flex032/uploads/quantasylum/original/1X/942860dd4314bb4b94ed8aaa67c4413c12250091.png)

Then the resulting graph is as follows. Note that we output 0 dBV, but it’s measured as 2.21 dBV because of the offset we specified. So, that gives us the correct value.

 ![image](https://canada1.discourse-cdn.com/flex032/uploads/quantasylum/original/1X/a5d80c20a59296c3ed5e4266c40060084ee0bc31.png)

And then I can change the Y axis title in the graph tool and I get:

 ![image](https://canada1.discourse-cdn.com/flex032/uploads/quantasylum/original/1X/ee19d6f44a51531ec89394e508dd7fe20919ee65.png)

So, with a little cheating you can get there.

---

<div class="post-metadata">

**Author:** ![M2Circuits](https://avatars.discourse-cdn.com/v4/letter/m/ecb155/32.png) [@M2Circuits](https://forum.quantasylum.com/u/M2Circuits)\
**Post date:** [June 18, 2020, 9:44pm UTC](https://forum.quantasylum.com/t/test-plugin-scale-units/117/3 "2020-06-18T21:44:22Z")

</div>

Hi Matt,

Thank you for your response!

Hopefully you will be able to implement a units selection in either the test plugin dialog box or graph editor in a future update.

But for now, this will work ok.

Thank you!
